See our new 142/242 Low Odor/Ultra Clear series!

Bait Plastics, LLC

$115.99$429.99

Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector  = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings

Air Clamp/Vise

Air Clamp

$350.00

-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***

Aluminum Fishing Lure Molds

4.20″ Beaver

$74.99

4.2" Original Beaver

Original beaver mold, hard to beat a tried and true fish catcher. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes  standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

4.65″ Hawg

$74.99

4.65" Hog mold Single Cavity

The smaller hog at 4.65" long with our style of flappers for excellent action! by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Speedy Craw

$74.99

3.5" Speedy Craw Single Cavity

Aluminum Fishing Lure Molds

4″ Bug Mold

$70.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits.   Single Cavity

Aluminum Fishing Lure Molds

4″ Bug

$725.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA

Quality supplier for all Soft Bait Making products.

Bait Plastics offers soft bait supplies for the DIY lure maker.  We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.

Plastisol Additives

Floating Additive

$6.99$19.99

Floating Additive is used to give baits increased buoyancy {Float}.  Please note that overuse of flotation beads will effect bait color.

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes  standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

Epic Bait Molds 2.5″ Ned Craw

$160.00

The ned craw bait measures 2.5″ from tail to tip of claws.  Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity

New

Safety Products

Pyrex Microwave Cup

$11.95

16 ounce {2 CUPS} PYREX Microwave Cup for heating plastisol in a microwave.

Aluminum Fishing Lure Molds

4 Inch Croaker Frog

$144.99

4 Inch Croaker Frog 2 Cavity  

$10.94

Fluorescent Powder - Add to plastisol to create unique effects and light reflection, Color will vary dramatically with plastic color. Use in clear or colored plastic. Packed by fluid ounces.

  • Purple
  • Hot Pink
  • Chartreuse
  • Blue
  • Neon Green
  • Orange

Sale!

Safety Products

Spice Spoon

$7.99

  • Stainless Steel
  • Set of four
  • Smidgen
  • Dash
  • Pinch
  • Tad

$170.00

The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part.  This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]

$12.99

The Next Level 6210 is a premium CVC crew neck. This relaxed-fit short-sleeve t-shirt is fabric laundered 60/40 combed ringspun cotton/polyester made of 32 singles with a set-in 1x1 baby rib collar and tear away label. Material: Cotton, Cotton Blend, Fleece, Jersey, Polyester, Rayon

Safety Products

Thermometer

$6.95

Thermometer

$7.99$23.99

High Temp Polyester .062 HEX Glitter

Aluminum Fishing Lure Molds

Epic Bait Molds 18″ Mega Ribbon Tail

$144.99

At a full 18″ the Mega Ribbon is the one of the biggest (if not THE biggest) Ribbon Tail injection worm mold on the market! Featuring a 1/2″ diameter ribbed body, smooth section, and .08″ thick tail. The ribbed body / smooth area is 7.5″ long and the tail is 10.5″ long making for a grand total of […]

We love the opportunity to speak with our customers and can be reached

at 800-427-5819 or csr@baitplastics.com

Wanting to learn more about Bait Plastics formulas and making your own soft baits.  Click here for helpful tips! 

Feature Products

Scent

Scents

$9.99$177.99

The best scents on the market.  Add these scents to the finished baits or bag to attract your trophy fish!

  • Anise
  • Cappuccino
  • Crawfish Oil
  • Garlic
  • Herring

Plastisol Additives

UV Dipping Dye

$6.95

4 Ounce Dipping Dye with UV. Instantly change your baits color  

  • UV Clear
  • Green
  • Chartreuse
  • Orange
  • Red

$4.95$19.99

Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4