See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs). There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]
Mixer
Bait Plastics Spatula
- Engraved Bait Plastics on wooden handle with stainless steel tip.
- This handheld mixer is powered by 2 AA batteries and is perfect for remixing pigments and small bottles.
- This Mixer attached to a standard drill and is used to quickly mix 1 Gallon Jugs
- This Mixer attaches to a standard drill and is used to quickly mix 5 gallon pails.
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Aluminum Fishing Lure Molds
At a full 18″ the Mega Ribbon is the one of the biggest (if not THE biggest) Ribbon Tail injection worm mold on the market! Featuring a 1/2″ diameter ribbed body, smooth section, and .08″ thick tail. The ribbed body / smooth area is 7.5″ long and the tail is 10.5″ long making for a grand total of […]
Aluminum Fishing Lure Molds
This 7 Inch ribbed Curly Tail Grub’s body thickness is .65″, the body length from nose to base of tail is 2.45″ and the curly tail is .07″ thick. The total length of this bait with its tail extended is 7 inches. 2 Cavity
Aluminum Fishing Lure Molds
The 3 Inch Stinger Ned measures 3" from tip to tail and the thick end of the bait is .45" thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads.
Mold size - 7in x 3in Number of cavities - 8 Made in the USA from 6061 Aluminum
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
All
Color Wheel For mixing different colors. Find your specific color by using this simple color wheel guide.
Safety Products
16 ounce {2 CUPS} PYREX Microwave Cup for heating plastisol in a microwave.
Aluminum Fishing Lure Molds
The 4″ long Slick Swimmer paddle tail swimbait’s body is .6″ thick and .375″ wide. This is a 6 cavity “top shot” mold which allows you to use two injectors and a mixing block (not included) to shoot top/bottom laminated baits.
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4