See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
40 Cavity tail mold that will fit in our 18 cavity stick bait mold.
Injectors
Hand Injectors with Locking Pins. 4oz Injector Series 1 = $105.99 6oz Injector=$115.99 8oz Injector = $125.99 10oz Injector = $135.99 Dual 4oz Injector Kit = $299.99 includes 2 Injectors and kit Dual 6oz injector = $310.99 includes 2 injectors and kit Dual 8oz injector=$329.99 includes 2 injectors and kit Dual 10oz injector=$349.99 includes 2 injectors and kit Dual Injector Kit= $115.99 only the kit Triple 4oz Injector Kit = $409.99 includes 3 Injectors and kit Triple 6oz Injector=$429.99 includes 3injectors and kit Triple 8oz Injector=$449.99 includes 3injectors and kit Triple 10oz Injector=$469.99 includes 3injectors and kit Triple Injector Kit = $115.99 only the kit All injectors Comes with 2 O-Rings
Plastisol Additives
Add this softener to any of the plastisol's offered to dial in the hardness of your finished bait.
Flex X
Years in the making patent pending from Bait Plastics. This unique blend of proprietary ingredients is both non phthalate and non PVC. Not intended for microwave. Set temperature 400F. Best processed using a convection pan, presto pot with beaker, shooting star, or a hot pan. if not using mixing pot, keep stirring to prevent burning or over heat. Mix until water clear and free of air bubbles. Comes with 1lb of Salt Works with all standard injectors and molds. Approximately 6lbs per 1 gallon container. Super clear, stretchy, low odor, and glossy. Much more durable than stand pvc plastics. See video below!!!
Melting Pots
Mixing Melting Pot Mixer attached, mixes while heating, Master heat control regulates the desired cooking temperature automatically. Kit Includes: 6 Quart, 8 Quart, or 10 Quart Pot Mixer Lid ASSM Power Cord Mixer Custom stand offs with high temp washers.
Aluminum Fishing Lure Molds
The 2 Inch Sandworm bait measures 2″ from end to end and the bait’s round/ribbed body section measures .215″ wide x .175″ tall at the thickest part. The tiny projections/legs along the sides of the body are flat on one side, rounded on other and taper to a point. This allows for lots of movement […]
Aluminum Fishing Lure Molds
Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT
The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4