See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
40 Cavity tail mold that will fit in our 18 cavity stick bait mold.
- 112 Super Soft
- 142 Super Soft/Low Odor/Ultra Clear
- 152 Soft
- 212 Medium
- 242 Medium/Low Odor/Ultra Clear
- 262 Medium / Saltwater
- 292 medium/hard/low odor/ulra clear
- 312 Saltwater
- 342 Hard/Low Odor/UltraClear
- 362 Saltwater Super Tough
Aluminum Fishing Lure Molds
Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT
The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]
Mixer
Bait Plastics Spatula
- Engraved Bait Plastics on wooden handle with stainless steel tip.
- This handheld mixer is powered by 2 AA batteries and is perfect for remixing pigments and small bottles.
- This Mixer attached to a standard drill and is used to quickly mix 1 Gallon Jugs
- This Mixer attaches to a standard drill and is used to quickly mix 5 gallon pails.
Aluminum Fishing Lure Molds
The 2 Inch Crappie Slayer measures 2″ long from tip to tail and the thickest part of the body is .36″ tall and 25″ wide. It has a deep bellied baby shad shape with a long thin tail designed specifically for crappie fishing. This mold works with a variety of plastisol hardnesses. This bait is best rigged on 1/64-1/16oz […]
3 Gallons of Plastisol
- Choose Formula
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Safety Products
- Stainless Steel
- Set of four
- Smidgen
- Dash
- Pinch
- Tad
Aluminum Fishing Lure Molds
The 2 Inch Curly Tail Grub bait is just under 2 inches from nose to tip of tail with the tail extended. It features a ribbed body that has a thickness of .25″ and length of .85″. The tail is thin and very “curled” to create a very flowing back/forth twisting motion while on the […]
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4