See our new 142/242 Low Odor/Ultra Clear series!

Bait Plastics, LLC

$115.99$429.99

Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector  = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings

Air Clamp/Vise

Air Clamp

$350.00

-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***

Aluminum Fishing Lure Molds

4.20″ Beaver

$74.99

4.2" Original Beaver

Original beaver mold, hard to beat a tried and true fish catcher. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes  standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

4.65″ Hawg

$74.99

4.65" Hog mold Single Cavity

The smaller hog at 4.65" long with our style of flappers for excellent action! by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Speedy Craw

$74.99

3.5" Speedy Craw Single Cavity

Aluminum Fishing Lure Molds

4″ Bug Mold

$70.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits.   Single Cavity

Aluminum Fishing Lure Molds

4″ Bug

$725.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA

Quality supplier for all Soft Bait Making products.

Bait Plastics offers soft bait supplies for the DIY lure maker.  We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.

$140.00

The 4.6″ Freakin Frog is a top water frog bait.  It’s legs kick/flop to create a small splash of water and a bubble trail as it is retrieved on a slow/moderate to fast retrieve.  The body of this bait is .85″ wide and .52″ thick.  The body also features a life-like profile with bumps down the […]

Aluminum Fishing Lure Molds

6 Inch Wicked Worm

$119.99

6 Inch Wicked Worm 2 Cavity Mold  

Aluminum Fishing Lure Molds

Epic Bait Molds 9″ Finesse Worm

$169.99

The 9 Inch Pintail Worm is 9 inches total length with a diameter of .35″ at the thickest part of the body that tapers down to .125″ in diameter at the tip of the tail.  The taper of the bait starts behind the egg sack area to leave the front of the bait thick where the hook […]

Plastisol Additives

UV Dipping Dye

$6.95

4 Ounce Dipping Dye with UV. Instantly change your baits color  

  • UV Clear
  • Green
  • Chartreuse
  • Orange
  • Red

$99.99$249.99

High Quality, High Strength TIN CURE RTV Silicone POLYSOL's RTV silicone mold making rubber is a two-component material.   There is a Part A and a Part B that is mixed together at a 10/1 ratio APPLICATIONS: -
  • Soft baits / Lures {Plastisol}
  • Wax
  • Soap
  • UltraCal 30
  • EpoxyLow melt metals (up to 400 degrees Max)
  • Polyester
  • Fiberglass Resign
  • Plaster
  • Urethane Rubber & Plastic
  • HydroCal White
MIXING: Mix Part A and Part B at a 10/1 ratio.  Once the two components are mixed thoroughly you will have roughly 45 minutes to pour the mixture. CURING:  After the mixture is poured it will fully cure in 12 Hours. PROPERTIES Mix Ratio: 10/1 by weight Base Color - Beige Catalyst Color - Blue Specific Gravity - 1.07 Viscosity (cPs) - 16,000 Pot Life (pour time) - 45 min. Tensile - 600 Elongation, % -  160 Durometer, Shore A = 45/50 Tear Strength - 25 Materials Recommended:
  • Digital Gram or Digital Postage Scale
  • Mixing Containers
  • Stir Sticks
  • Latex or Nitrile Gloves

$282.00

Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™)

  • If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void.
  • These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties.
  • When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result from the first use.)
  • To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
 

Sale!
$159.99

 

  • 112 Super Soft
  • 142 Super Soft/Low Odor/Ultra Clear
  • 152 Soft
  • 212 Medium
  • 242 Medium/Low Odor/Ultra Clear
  • 262 Medium / Saltwater
  • 292 medium/hard/low odor/ulra clear
  • 312 Saltwater
  • 342 Hard/Low Odor/UltraClear
  • 362 Saltwater Super Tough

Plastisol Additives

Sinking Additive

$9.95$49.95

Sinking Additive is used to give baits a slow sinking action in the water.  Please note that overuse of sinking additive will effect bait color.

New

Safety Products

Pyrex Microwave Cup

$11.95

16 ounce {2 CUPS} PYREX Microwave Cup for heating plastisol in a microwave.

$4.95$19.99

Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4

Aluminum Fishing Lure Molds

Epic 2.0″ Battle Grub

$170.00

The 2 Inch Battle Grub measures 2 inches long from tip to tail and the thickest part of the body is .36″ in across.  It has a grub shaped body for easy rigging on small jigs, a wide but flat tail that has lots of up/down action and spikes along both sides to add texture and more […]

$140.00

The 6 Inch Finesse Worm is 6 inches total length with a diameter of .33″ at the thickest part of the body.  The bottom of the bait is flat in overall shape but the ribbing on the body goes all the way around the worm. Mold size – 3″x7″ Number of cavities – 5 All molds are […]

We love the opportunity to speak with our customers and can be reached

at 800-427-5819 or csr@baitplastics.com

Wanting to learn more about Bait Plastics formulas and making your own soft baits.  Click here for helpful tips! 

Feature Products

Scent

Scents

$9.99$177.99

The best scents on the market.  Add these scents to the finished baits or bag to attract your trophy fish!

  • Anise
  • Cappuccino
  • Crawfish Oil
  • Garlic
  • Herring

Plastisol Additives

UV Dipping Dye

$6.95

4 Ounce Dipping Dye with UV. Instantly change your baits color  

  • UV Clear
  • Green
  • Chartreuse
  • Orange
  • Red

$4.95$19.99

Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4