See our new 142/242 Low Odor/Ultra Clear series!

Bait Plastics, LLC

$115.99$429.99

Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector  = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings

Air Clamp/Vise

Air Clamp

$350.00

-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***

Aluminum Fishing Lure Molds

4.20″ Beaver

$74.99

4.2" Original Beaver

Original beaver mold, hard to beat a tried and true fish catcher. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes  standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

4.65″ Hawg

$74.99

4.65" Hog mold Single Cavity

The smaller hog at 4.65" long with our style of flappers for excellent action! by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Speedy Craw

$74.99

3.5" Speedy Craw Single Cavity

Aluminum Fishing Lure Molds

4″ Bug Mold

$70.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits.   Single Cavity

Aluminum Fishing Lure Molds

4″ Bug

$725.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA

Quality supplier for all Soft Bait Making products.

Bait Plastics offers soft bait supplies for the DIY lure maker.  We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.

Accessories

Bait Plastics Tank

$8.99

There's a reason this one is called the Ideal Racerback Tank. The name speaks for itself. It's lightweight, comfortable and versatile. Material: Cotton, Cotton Blend, Jersey, Polyester

$7.99$23.99

High Temp Polyester Glitter .015 HEX  

Aluminum Fishing Lure Molds

Epic Bait Molds 3″ Epic Prey Bait

$159.99

The 3 Inch Epic PreyBait, “hand injection” style mold was designed as part of a collaboration with Marling Baits. The Epic PreyBait is a boot tail swimbait with a rear fin designed to have an intense action with realistic presentation at any speed, with a kick and wobble on the fall. This bait/mold does not have a hook slot and is intended to […]

Aluminum Fishing Lure Molds

Epic 2.0″ Battle Grub

$170.00

The 2 Inch Battle Grub measures 2 inches long from tip to tail and the thickest part of the body is .36″ in across.  It has a grub shaped body for easy rigging on small jigs, a wide but flat tail that has lots of up/down action and spikes along both sides to add texture and more […]

Sale!

Safety Products

Spice Spoon

$7.99

  • Stainless Steel
  • Set of four
  • Smidgen
  • Dash
  • Pinch
  • Tad

$145.00

The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs).  There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]

Aluminum Fishing Lure Molds

6 Inch Wicked Worm

$119.99

6 Inch Wicked Worm 2 Cavity Mold  

$135.00$235.00

The Classic Stickbait features a worm-like rib texture and a gently tapered tail. Designed for the wacky rig, texas rig, carolina rig and other bass fishing techniques. 5″ Classic Stickbait – 4 Cavity Mold size – 3″x6.125″ 8 Cavity Mold size – 6″x6.125″ Bait size – 5″ long x 0.393″ thick More sizes coming soon, email us at EpicBaitMolds@gmail.com if you […]

$135.99

2 Gallons of  Plastisol

  • Choose Formula
Scent  4 Pigments Choices  {4 Ounces Each} 4 Color Choices of .040 Hex High Temp Glitter  {4 Ounces Each} 25 Bait Bags {Pick Size}    

$135.00

The 3 Inch Stinger Ned measures 3" from tip to tail and the thick end of the bait is .45" thick.  The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads.

Mold size - 7in x 3in Number of cavities - 8 Made in the USA from 6061 Aluminum

Safety Products

Hot Mill Gloves

$10.99

Hot Mill Gloves

We love the opportunity to speak with our customers and can be reached

at 800-427-5819 or csr@baitplastics.com

Wanting to learn more about Bait Plastics formulas and making your own soft baits.  Click here for helpful tips! 

Feature Products

Scent

Scents

$9.99$177.99

The best scents on the market.  Add these scents to the finished baits or bag to attract your trophy fish!

  • Anise
  • Cappuccino
  • Crawfish Oil
  • Garlic
  • Herring

Plastisol Additives

UV Dipping Dye

$6.95

4 Ounce Dipping Dye with UV. Instantly change your baits color  

  • UV Clear
  • Green
  • Chartreuse
  • Orange
  • Red

$4.95$19.99

Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4