See our new 142/242 Low Odor/Ultra Clear series!

Bait Plastics, LLC

$115.99$429.99

Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector  = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings

Air Clamp/Vise

Air Clamp

$350.00

-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***

Aluminum Fishing Lure Molds

4.20″ Beaver

$74.99

4.2" Original Beaver

Original beaver mold, hard to beat a tried and true fish catcher. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes  standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

4.65″ Hawg

$74.99

4.65" Hog mold Single Cavity

The smaller hog at 4.65" long with our style of flappers for excellent action! by Kearby Design & Manufacturing LLC Made in USA

Aluminum Fishing Lure Molds

3.5″ Speedy Craw

$74.99

3.5" Speedy Craw Single Cavity

Aluminum Fishing Lure Molds

4″ Bug Mold

$70.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits.   Single Cavity

Aluminum Fishing Lure Molds

4″ Bug

$725.00

4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA

Quality supplier for all Soft Bait Making products.

Bait Plastics offers soft bait supplies for the DIY lure maker.  We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.

$185.00

This “fluke style” or “jerk bait” style bait measures 5 inches from nose to tail with a body width of .38″ and a mid body thickness of .6″.  The belly features a deep hook slot to allow great hookup ratios on ewg style hooks.  The back features a divot down the center for aligning and […]

$9.95$17.95

.025 HEX Fluorescent GLITTER

  • Pink
  • Lime
  • Yellow
  • Orange
  • Blue

$70.00$165.00

This 3 Inch Curly Tail Grub’s body thickness is .36″, the body length from nose to base of tail is 1.05″ and the curly tail is .05″ thick.  The overall length of the bait is 3 inches with the tail extended/hanging. These grubs feature unbeatable tail action and shoot perfect. 2 Cavity Mold Dimensions – 5″x2″ 10 Cavity […]

Sale!

Flex X

Flex X 200

$75.99

Years in the making patent pending from Bait Plastics. This unique blend of proprietary ingredients is both non phthalate and non PVC. Not intended for microwave.  Set temperature 400F. Best processed using a convection pan, presto pot with beaker, shooting star, or a hot pan. if not using mixing pot, keep stirring to prevent burning or over heat. Mix until water clear and free of air bubbles. Comes with 1lb of Salt Works with all standard injectors and molds. Approximately 6lbs per 1 gallon container. Super clear, stretchy, low odor, and glossy. Much more durable than stand pvc plastics. See video below!!!  

Thank your for your purchase from Bait Plastics. Below are some instructions and helpful tips. Lure Plastisol Formulations – Bait Plastics offers the below formulations for you exact needs. 112 Super Soft – This formula is great for drop shot and finesse baits. This is our softest formula and guarantees great action in the water. […]

Safety Products

Thermometer

$6.95

Thermometer

$282.00

Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™)

  • If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void.
  • These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties.
  • When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result from the first use.)
  • To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
 

$7.64$14.24

Highlight Powder - Add to plastisol to create unique effects and light reflection, Color will vary dramatically with plastic color. Use in clear or colored plastic. Packed by fluid ounces.

  • Blue Highlight
  • Violet Highlight
  • Gold Highlight
  • Green Highlight
  • Red Highlight
  • Copper Highlight

Aluminum Fishing Lure Molds

Epic Bait Molds 2″ Sand Worm

$189.99

The 2 Inch Sandworm bait measures 2″ from end to end and the bait’s round/ribbed body section measures .215″ wide x .175″ tall at the thickest part. The tiny projections/legs along the sides of the body are flat on one side, rounded on other and taper to a point. This allows for lots of movement […]

New

Safety Products

Pyrex Microwave Cup

$11.95

16 ounce {2 CUPS} PYREX Microwave Cup for heating plastisol in a microwave.

Aluminum Fishing Lure Molds

3 Inch Ned Worm

$159.99

3 Inch Ned Worm 10 Cavity  

$140.00

The 4.6″ Freakin Frog is a top water frog bait.  It’s legs kick/flop to create a small splash of water and a bubble trail as it is retrieved on a slow/moderate to fast retrieve.  The body of this bait is .85″ wide and .52″ thick.  The body also features a life-like profile with bumps down the […]

We love the opportunity to speak with our customers and can be reached

at 800-427-5819 or csr@baitplastics.com

Wanting to learn more about Bait Plastics formulas and making your own soft baits.  Click here for helpful tips! 

Feature Products

Scent

Scents

$9.99$177.99

The best scents on the market.  Add these scents to the finished baits or bag to attract your trophy fish!

  • Anise
  • Cappuccino
  • Crawfish Oil
  • Garlic
  • Herring

Plastisol Additives

UV Dipping Dye

$6.95

4 Ounce Dipping Dye with UV. Instantly change your baits color  

  • UV Clear
  • Green
  • Chartreuse
  • Orange
  • Red

$4.95$19.99

Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4