See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Melting Pots
Mixing Melting Pot Mixer attached, mixes while heating, Master heat control regulates the desired cooking temperature automatically. Kit Includes: 6 Quart, 8 Quart, or 10 Quart Pot Mixer Lid ASSM Power Cord Mixer Custom stand offs with high temp washers.
Aluminum Fishing Lure Molds
The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]
1 Gallon of Plastisol
- Choose Formula
All
Pearl Powder - Add Pearl Powder to hot plastisol to create unique effects and light reflection. 1 Fluid ounce container 2 Fluid Ounce container
- Silk Silver New
- Black Pearl
- Pink Pearl
- Dark Blue Pearl
- Sky Blue Pearl
- Copper Pearl
- Dark Red Pearl
- Brilliant Gold
- Green Apple Pearl
- Purple Pearl
- Dark Green Pearl
- Silver Pearl
- White Pearl
Air Clamp/Vise
Recommended air pressure 110 to 140PSI. If possible, use an air inline filter to extend the cylinder life. Always check your compressor for moisture. 6" Base Keep molds centered to get the best out of this clamp. Do not leave plugged in with pressure when not in use. Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. Clean with compressed air. Do not use chemicals or abrasives. (wd40 safe for cleaning) Do not exceed 140 psi. Servicing. Add very little Tool oil once every month. (About 4 drops is all you need to lube the system.) (Do not use WD40 in the air lines.)
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
All
Glow Powders - Add Glow Powder to your plastisol to create glowing baits
- Blue
- Green
- Aqua
Plastisol Additives
The Plastisol made by PolySol and distributed by Bait Plastics typically does not require any additional stabilizer, but this high grade stabilizer will correct any yellowing issues you may see after several reheats.
Plastisol Additives
Floating Additive is used to give baits increased buoyancy {Float}. Please note that overuse of flotation beads will effect bait color.
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4