Pearls, Highlights, & Glow Powders

8 Products

Liquid Plastisol

6 Products

Aluminum Fishing Lure Molds

36 Products

Stick / Worm Molds

10 Products

See our new 142/242 Low Odor/Ultra Clear series!

Bait Plastics, LLC

Quick View

Soft Bait Starter Kits

Motivated Crappie Starter Kit

$139.99

Crappie Starter Kit 2 Gallons of Plastisol 112 212 Scent Garlic 4 Pigments Choices Flu Pink Monkey Milk Chartreuse Black 4 Color Choices of .015 Hex High Temp Glitter Holo Gold Holo Silver Black Red 25 Bait Bags 3×3

Add to cart

Quick View

Soft Bait Starter Kits

Motivated Bass Starter Kit

$135.99

Bass Starter kit 2 Gallons of Plastisol Pm212 PM262 Scent Garlic 4 Pigments Choices White Black Green Pumpkin Watermelon 4 Color Choices of .015 Hex High Temp Glitter Black Red Royal Blue Purple 25 Bait Bags 7×4 1/4

Add to cart

Quick View

Injectors

N2 Injectors Series 2

Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings

Select options

Quick View

Air Clamp/Vise

Air Clamp

$350.00

-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***

Add to cart

Quick View

Out of stock

Aluminum Fishing Lure Molds

4.20″ Beaver

$74.99

4.2" Original Beaver

Original beaver mold, hard to beat a tried and true fish catcher. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Quick View

Out of stock

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Quick View

Out of stock

Aluminum Fishing Lure Molds

4.65″ Hawg

$74.99

4.65" Hog mold Single Cavity

The smaller hog at 4.65" long with our style of flappers for excellent action! by Kearby Design & Manufacturing LLC Made in USA

Quick View

Aluminum Fishing Lure Molds

3.5″ Speedy Craw

$74.99

3.5" Speedy Craw Single Cavity

Add to cart

Quality supplier for all Soft Bait Making products.

Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.

Sale!

Quick View

Flex X

Flex X 200

Years in the making patent pending from Bait Plastics. This unique blend of proprietary ingredients is both non phthalate and non PVC. Not intended for microwave. Set temperature 400F. Best processed using a convection pan, presto pot with beaker, shooting star, or a hot pan. if not using mixing pot, keep stirring to prevent burning or over heat. Mix until water clear and free of air bubbles. Comes with 1lb of Salt Works with all standard injectors and molds. Approximately 6lbs per 1 gallon container. Super clear, stretchy, low odor, and glossy. Much more durable than stand pvc plastics. See video below!!!

Add to cart

Epic Bait Molds 3" SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) - 6 CAVITY TOP SHOOT

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT

$190.00

The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]

Add to cart

Quick View

All

.015 High Temp Glitter

High Temp Polyester Glitter .015 HEX

Select options

Quick View

Plastisol Additives

UV Dipping Dye

$6.95

4 Ounce Dipping Dye with UV. Instantly change your baits color

UV Clear
Green
Chartreuse
Orange
Red

Select options

Quick View

Safety Products

Hot Mill Gloves

$10.99

Hot Mill Gloves

Add to cart

Epic Bait Molds 5 Inch CLASSIC STICKBAIT MOLDS - 4 and 8 Cavity

Quick View

Out of stock

Aluminum Fishing Lure Molds

Epic Bait Molds 5 Inch CLASSIC STICKBAIT MOLDS – 4 and 8 Cavity

The Classic Stickbait features a worm-like rib texture and a gently tapered tail. Designed for the wacky rig, texas rig, carolina rig and other bass fishing techniques. 5″ Classic Stickbait – 4 Cavity Mold size – 3″x6.125″ 8 Cavity Mold size – 6″x6.125″ Bait size – 5″ long x 0.393″ thick More sizes coming soon, email us at EpicBaitMolds@gmail.com if you […]

Select options

Quick View

Plastisol Additives

Sinking Additive

Sinking Additive is used to give baits a slow sinking action in the water. Please note that overuse of sinking additive will effect bait color.

Select options

Quick View

Plastisol Additives

Floating Additive

Floating Additive is used to give baits increased buoyancy {Float}. Please note that overuse of flotation beads will effect bait color.

Select options

Epic Bait Molds 3" NED STINGER MOLD - 8 CAVITY

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 3″ NED STINGER MOLD – 8 CAVITY

$135.00

The Stinger Ned measures 3″ from tip to tail and the thick end of the bait is .45″ thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads. Mold size – 7in x 3in Number of cavities – 8 Made in […]

Add to cart

Quick View

Melting Pots

Mixing Melting Pot

Mixing Melting Pot Mixer attached, mixes while heating, Master heat control regulates the desired cooking temperature automatically. Kit Includes: 6 Quart, 8 Quart, or 10 Quart Pot Mixer Lid ASSM Power Cord Mixer Custom stand offs with high temp washers.

Select options

Quick View

Liquid Pigments

Premium Pigments

Tequila Sunrise
Red Shad
Limetreuse EX
Chartreuse EX
Monkey Milk
Turbo Pink
Turbo Green
Turbo Orange
Turbo Purple
June Bug EX
Turbo Blue
Blue Craw

Select options

Epic Bait Molds 5 INCH FLAPPIN DRAX MOLD - 2 CAVITY

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 5 INCH FLAPPIN DRAX MOLD – 2 CAVITY

$145.00

The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs). There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]

Add to cart