-
×
Epic Bait Molds 2" Sand Worm
1 × $189.99
Subtotal: $189.99
See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
$115.99 – $429.99
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
$350.00
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Out of stock
Aluminum Fishing Lure Molds
$74.99
4.2" Original Beaver
Original beaver mold, hard to beat a tried and true fish catcher.
Single Cavity
by Kearby Design & Manufacturing LLC
Made in USA
Aluminum Fishing Lure Molds
$74.99
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
$74.99
4.65" Hog mold Single Cavity
The smaller hog at 4.65" long with our style of flappers for excellent action!
by Kearby Design & Manufacturing LLC
Made in USA
Out of stock
Aluminum Fishing Lure Molds
$70.00
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
$725.00
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
$74.99
4.65" Hog mold Single Cavity
The smaller hog at 4.65" long with our style of flappers for excellent action!
by Kearby Design & Manufacturing LLC
Made in USA
Aluminum Fishing Lure Molds
$185.00
This “fluke style” or “jerk bait” style bait measures 5 inches from nose to tail with a body width of .38″ and a mid body thickness of .6″. The belly features a deep hook slot to allow great hookup ratios on ewg style hooks. The back features a divot down the center for aligning and […]
Sale!
Out of stock
Aluminum Fishing Lure Molds
$145.00
The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs). There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]
Plastisol Additives
$12.50 – $146.99
Add this softener to any of the plastisol's offered to dial in the hardness of your finished bait.
Injectors
$415.00
5.25" Stick bait very similiar to the big brand stick bait of this size. 18 Cavities Made in USA
Mixer
$5.95 – $14.95
Bait Plastics Spatula
- Engraved Bait Plastics on wooden handle with stainless steel tip.
- This handheld mixer is powered by 2 AA batteries and is perfect for remixing pigments and small bottles.
- This Mixer attached to a standard drill and is used to quickly mix 1 Gallon Jugs
- This Mixer attaches to a standard drill and is used to quickly mix 5 gallon pails.
Aluminum Fishing Lure Molds
$135.00
The Stinger Ned measures 3″ from tip to tail and the thick end of the bait is .45″ thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads. Mold size – 7in x 3in Number of cavities – 8 Made in […]
$92.99
1 Gallon of Plastisol
- Choose Formula
All
$10.94 – $60.44
Glow Powders - Add Glow Powder to your plastisol to create glowing baits
- Blue
- Green
- Aqua
All
$4.99
Color Wheel For mixing different colors. Find your specific color by using this simple color wheel guide.
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
$9.99 – $177.99
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
$6.95
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
$4.95 – $19.99
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4