Air Clamp
1 × $350.00 
3.5" Speedy Craw
1 × $74.99 
Spice Spoon
1 × $7.99 
Thermometer
1 × $6.95 Subtotal: $439.93
Soft Bait Starter Kits
Crappie Starter Kit 2 Gallons of Plastisol 112 212 Scent Garlic 4 Pigments Choices Flu Pink Monkey Milk Chartreuse Black 4 Color Choices of .015 Hex High Temp Glitter  Holo Gold Holo Silver Black Red 25 Bait Bags 3×3
Soft Bait Starter Kits
Bass Starter kit 2 Gallons of Plastisol Pm212 PM262 Scent Garlic 4 Pigments Choices White Black Green Pumpkin Watermelon 4 Color Choices of .015 Hex High Temp Glitter  Black Red Royal Blue Purple 25 Bait Bags 7×4 1/4
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Liquid Pigments
Safety Products
16 ounce {2 CUPS} PYREX Microwave Cup for heating plastisol in a microwave.
Aluminum Fishing Lure Molds
The 4.6″ Freakin Frog is a top water frog bait. It’s legs kick/flop to create a small splash of water and a bubble trail as it is retrieved on a slow/moderate to fast retrieve.  The body of this bait is .85″ wide and .52″ thick. The body also features a life-like profile with bumps down the […]
Aluminum Fishing Lure Molds
Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT
The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]
Aluminum Fishing Lure Molds
The 3 Inch Epic PreyBait, “hand injection” style mold was designed as part of a collaboration with Marling Baits. The Epic PreyBait is a boot tail swimbait with a rear fin designed to have an intense action with realistic presentation at any speed, with a kick and wobble on the fall. This bait/mold does not have a hook slot and is intended to […]
Aluminum Fishing Lure Molds
The 3 Inch Stinger Ned measures 3" from tip to tail and the thick end of the bait is .45" thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads.
Mold size - 7in x 3in Number of cavities - 8 Made in the USA from 6061 Aluminum
Air Clamp/Vise
Recommended air pressure 110 to 140PSI. If possible, use an air inline filter to extend the cylinder life. Always check your compressor for moisture. 6" Base Keep molds centered to get the best out of this clamp. Do not leave plugged in with pressure when not in use. Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. Clean with compressed air. Do not use chemicals or abrasives. (wd40 safe for cleaning) Do not exceed 140 psi. Servicing. Add very little Tool oil once every month. (About 4 drops is all you need to lube the system.) (Do not use WD40 in the air lines.)
Aluminum Fishing Lure Molds
The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]
Scent
The best scents on the market. Â Add these scents to the finished baits or bag to attract your trophy fish!
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4
