See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
The 9 Inch Pintail Worm is 9 inches total length with a diameter of .35″ at the thickest part of the body that tapers down to .125″ in diameter at the tip of the tail. The taper of the bait starts behind the egg sack area to leave the front of the bait thick where the hook […]
1 Gallon of Plastisol
- Choose Formula
Aluminum Fishing Lure Molds
The 4″ long Slick Swimmer paddle tail swimbait’s body is .6″ thick and .375″ wide. This is a 6 cavity “top shot” mold which allows you to use two injectors and a mixing block (not included) to shoot top/bottom laminated baits.
Aluminum Fishing Lure Molds
The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]
- 112 Super Soft
- 142 Super Soft/Low Odor/Ultra Clear
- 152 Soft
- 212 Medium
- 242 Medium/Low Odor/Ultra Clear
- 262 Medium / Saltwater
- 292 medium/hard/low odor/ulra clear
- 312 Saltwater
- 342 Hard/Low Odor/UltraClear
- 362 Saltwater Super Tough
Aluminum Fishing Lure Molds
This 12 inch Mega Curly Tail Grub’s body thickness is 1.38″, the body length is 5.5″ and the curly tail is .12″ thick. The total length of this bait with its tail extended is 12 inches. This is a single cavity mold that can be used for making laminate or solid color baits. You must use […]
Mixer
Bait Plastics Spatula
- Engraved Bait Plastics on wooden handle with stainless steel tip.
- This handheld mixer is powered by 2 AA batteries and is perfect for remixing pigments and small bottles.
- This Mixer attached to a standard drill and is used to quickly mix 1 Gallon Jugs
- This Mixer attaches to a standard drill and is used to quickly mix 5 gallon pails.
Aluminum Fishing Lure Molds
The Stinger Ned measures 3″ from tip to tail and the thick end of the bait is .45″ thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads. Mold size – 7in x 3in Number of cavities – 8 Made in […]
Aluminum Fishing Lure Molds
The 2 Inch Curly Tail Grub bait is just under 2 inches from nose to tip of tail with the tail extended. It features a ribbed body that has a thickness of .25″ and length of .85″. The tail is thin and very “curled” to create a very flowing back/forth twisting motion while on the […]
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4