Pearls, Highlights, & Glow Powders

8 Products

Liquid Plastisol

6 Products

Aluminum Fishing Lure Molds

36 Products

Stick / Worm Molds

10 Products

See our new 142/242 Low Odor/Ultra Clear series!

Bait Plastics, LLC

Quick View

Soft Bait Starter Kits

Motivated Crappie Starter Kit

$139.99

Crappie Starter Kit 2 Gallons of Plastisol 112 212 Scent Garlic 4 Pigments Choices Flu Pink Monkey Milk Chartreuse Black 4 Color Choices of .015 Hex High Temp Glitter Holo Gold Holo Silver Black Red 25 Bait Bags 3×3

Add to cart

Quick View

Soft Bait Starter Kits

Motivated Bass Starter Kit

$135.99

Bass Starter kit 2 Gallons of Plastisol Pm212 PM262 Scent Garlic 4 Pigments Choices White Black Green Pumpkin Watermelon 4 Color Choices of .015 Hex High Temp Glitter Black Red Royal Blue Purple 25 Bait Bags 7×4 1/4

Add to cart

Quick View

Injectors

N2 Injectors Series 2

Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings

Select options

Quick View

Air Clamp/Vise

Air Clamp

$350.00

-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***

Add to cart

Quick View

Out of stock

Aluminum Fishing Lure Molds

4.20″ Beaver

$74.99

4.2" Original Beaver

Original beaver mold, hard to beat a tried and true fish catcher. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Quick View

Out of stock

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Quick View

Out of stock

Aluminum Fishing Lure Molds

4.65″ Hawg

$74.99

4.65" Hog mold Single Cavity

The smaller hog at 4.65" long with our style of flappers for excellent action! by Kearby Design & Manufacturing LLC Made in USA

Quick View

Aluminum Fishing Lure Molds

3.5″ Speedy Craw

$74.99

3.5" Speedy Craw Single Cavity

Add to cart

Quality supplier for all Soft Bait Making products.

Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.

Epic Bait Molds 6.2 INCH LIZARD MOLD - 4 CAVITY

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 6.2 INCH LIZARD MOLD – 4 CAVITY

$185.00

The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]

Add to cart

Quick View

Out of stock

Aluminum Fishing Lure Molds

3.5″ Craw

$74.99

3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA

Quick View

Plastisol Additives

Heat Stabilizer

The Plastisol made by PolySol and distributed by Bait Plastics typically does not require any additional stabilizer, but this high grade stabilizer will correct any yellowing issues you may see after several reheats.

Select options

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 2″ Sand Worm

$189.99

The 2 Inch Sandworm bait measures 2″ from end to end and the bait’s round/ribbed body section measures .215″ wide x .175″ tall at the thickest part. The tiny projections/legs along the sides of the body are flat on one side, rounded on other and taper to a point. This allows for lots of movement […]

Add to cart

Epic Bait Molds 3" NED STINGER MOLD - 8 CAVITY

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 3″ NED STINGER MOLD – 8 CAVITY

$135.00

The Stinger Ned measures 3″ from tip to tail and the thick end of the bait is .45″ thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads. Mold size – 7in x 3in Number of cavities – 8 Made in […]

Add to cart

Quick View

Melting Pots

Mixing Melting Pot

Mixing Melting Pot Mixer attached, mixes while heating, Master heat control regulates the desired cooking temperature automatically. Kit Includes: 6 Quart, 8 Quart, or 10 Quart Pot Mixer Lid ASSM Power Cord Mixer Custom stand offs with high temp washers.

Select options

Quick View

All

Helpful Tips!

Thank your for your purchase from Bait Plastics. Below are some instructions and helpful tips. Lure Plastisol Formulations – Bait Plastics offers the below formulations for you exact needs. 112 Super Soft – This formula is great for drop shot and finesse baits. This is our softest formula and guarantees great action in the water. […]

Quick View

Out of stock

Hand Injectors

Injector #2

Hand Injectors with screw on tip. 4 Ounce Injector = $89.99 6 Ounce Injector = $99.99 10 Ounce Injector = $119.99 12 Ounce Injector = $129.99

Select options

Epic Bait Molds 5 INCH FLAPPIN DRAX MOLD - 2 CAVITY

Quick View

Aluminum Fishing Lure Molds

Epic Bait Molds 5 INCH FLAPPIN DRAX MOLD – 2 CAVITY

$145.00

The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs). There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]

Add to cart

Quick View

Accessories

Bait Plastics T-Shirt

$12.99

The Next Level 6210 is a premium CVC crew neck. This relaxed-fit short-sleeve t-shirt is fabric laundered 60/40 combed ringspun cotton/polyester made of 32 singles with a set-in 1x1 baby rib collar and tear away label. Material: Cotton, Cotton Blend, Fleece, Jersey, Polyester, Rayon

Select options