See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Plastisol Additives
The Plastisol made by PolySol and distributed by Bait Plastics typically does not require any additional stabilizer, but this high grade stabilizer will correct any yellowing issues you may see after several reheats.
Flex X
Years in the making patent pending from Bait Plastics. This unique blend of proprietary ingredients is both non phthalate and non PVC. Not intended for microwave. Set temperature 400F. Best processed using a convection pan, presto pot with beaker, shooting star, or a hot pan. if not using mixing pot, keep stirring to prevent burning or over heat. Mix until water clear and free of air bubbles. Comes with 1lb of Salt Works with all standard injectors and molds. Approximately 6lbs per 1 gallon container. Super clear, stretchy, low odor, and glossy. Much more durable than stand pvc plastics. See video below!!!
Aluminum Fishing Lure Molds
The 2 Inch Sandworm bait measures 2″ from end to end and the bait’s round/ribbed body section measures .215″ wide x .175″ tall at the thickest part. The tiny projections/legs along the sides of the body are flat on one side, rounded on other and taper to a point. This allows for lots of movement […]
All
Color Wheel For mixing different colors. Find your specific color by using this simple color wheel guide.
Aluminum Fishing Lure Molds
The 2 Inch Curly Tail Grub bait is just under 2 inches from nose to tip of tail with the tail extended. It features a ribbed body that has a thickness of .25″ and length of .85″. The tail is thin and very “curled” to create a very flowing back/forth twisting motion while on the […]
Aluminum Fishing Lure Molds
The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]
Liquid Plastisol
- 112 Super Soft
- 142 Super Soft/Low Odor/Ultra Clear
- 152 Soft
- 212 Medium
- 242 Medium/Low Odor/Ultra Clear
- 262 Medium / Saltwater
- 292 medium/hard/low odor/ulra clear
- 312 Saltwater
- 342 Hard/Low Odor/Ultra Clear
- 362 Saltwater Super Tough
Plastisol Additives
Sinking Additive is used to give baits a slow sinking action in the water. Please note that overuse of sinking additive will effect bait color.
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4