See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Aluminum Fishing Lure Molds
The 3 Inch Stinger Ned measures 3" from tip to tail and the thick end of the bait is .45" thick. The body has a thin angled rib texture and a pointed, pyramid shaped tail. Designed for use with a ned rig style jig heads.
Mold size - 7in x 3in Number of cavities - 8 Made in the USA from 6061 Aluminum
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Air Clamp/Vise
Recommended air pressure 110 to 140PSI. If possible, use an air inline filter to extend the cylinder life. Always check your compressor for moisture. 6" Base Keep molds centered to get the best out of this clamp. Do not leave plugged in with pressure when not in use. Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. Clean with compressed air. Do not use chemicals or abrasives. (wd40 safe for cleaning) Do not exceed 140 psi. Servicing. Add very little Tool oil once every month. (About 4 drops is all you need to lube the system.) (Do not use WD40 in the air lines.)
Aluminum Fishing Lure Molds
The 9 Inch Pintail Worm is 9 inches total length with a diameter of .35″ at the thickest part of the body that tapers down to .125″ in diameter at the tip of the tail. The taper of the bait starts behind the egg sack area to leave the front of the bait thick where the hook […]
Aluminum Fishing Lure Molds
The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs). There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]
Bait Plastics Accessories
The Chill-N-Reel Lets you go fishing without putting your drink down! It's a hand-line fishing reel on the side of an insulated drink holder. The Chill-N-Reel is easy to just about any age. Simply pitch the line(with bait on the hook)in the water with the logo-side facing away from you and your favorite beverage in the drink insulator, wait, tug when you get a bite, and hand-reel with your fish on! It's that easy! The patented The Chill-N-Reel drink holder comes equipped with 50ft of 8lb test line, a hook, sinker, and of course a Chill-N-Reel drink insulator to keep your beverage of choice nice and cool so you can "Reel 'em in Cold!"
Plastisol Additives
Add this softener to any of the plastisol's offered to dial in the hardness of your finished bait.
All
Thank your for your purchase from Bait Plastics. Below are some instructions and helpful tips. Lure Plastisol Formulations – Bait Plastics offers the below formulations for you exact needs. 112 Super Soft – This formula is great for drop shot and finesse baits. This is our softest formula and guarantees great action in the water. […]
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4