See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]
3 Gallons of Plastisol
- Choose Formula
Aluminum Fishing Lure Molds
The 2 Inch Crappie Slayer measures 2″ long from tip to tail and the thickest part of the body is .36″ tall and 25″ wide. It has a deep bellied baby shad shape with a long thin tail designed specifically for crappie fishing. This mold works with a variety of plastisol hardnesses. This bait is best rigged on 1/64-1/16oz […]
2 Gallons of Plastisol
- Choose Formula
Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™)
- If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void.
- These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties.
- When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result from the first use.)
- To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
Injectors
Hand Injectors with Locking Pins. 4oz Injector Series 1 = $105.99 6oz Injector=$115.99 8oz Injector = $125.99 10oz Injector = $135.99 Dual 4oz Injector Kit = $299.99 includes 2 Injectors and kit Dual 6oz injector = $310.99 includes 2 injectors and kit Dual 8oz injector=$329.99 includes 2 injectors and kit Dual 10oz injector=$349.99 includes 2 injectors and kit Dual Injector Kit= $115.99 only the kit Triple 4oz Injector Kit = $409.99 includes 3 Injectors and kit Triple 6oz Injector=$429.99 includes 3injectors and kit Triple 8oz Injector=$449.99 includes 3injectors and kit Triple 10oz Injector=$469.99 includes 3injectors and kit Triple Injector Kit = $115.99 only the kit All injectors Comes with 2 O-Rings
All
Thank your for your purchase from Bait Plastics. Below are some instructions and helpful tips. Lure Plastisol Formulations – Bait Plastics offers the below formulations for you exact needs. 112 Super Soft – This formula is great for drop shot and finesse baits. This is our softest formula and guarantees great action in the water. […]
Plastisol Additives
Sinking Additive is used to give baits a slow sinking action in the water. Please note that overuse of sinking additive will effect bait color.
Aluminum Fishing Lure Molds
Epic Bait Molds 5 Inch CLASSIC STICKBAIT MOLDS – 4 and 8 Cavity
The Classic Stickbait features a worm-like rib texture and a gently tapered tail. Designed for the wacky rig, texas rig, carolina rig and other bass fishing techniques. 5″ Classic Stickbait – 4 Cavity Mold size – 3″x6.125″ 8 Cavity Mold size – 6″x6.125″ Bait size – 5″ long x 0.393″ thick More sizes coming soon, email us at EpicBaitMolds@gmail.com if you […]
Aluminum Fishing Lure Molds
The 4″ long Slick Swimmer paddle tail swimbait’s body is .6″ thick and .375″ wide. This is a 6 cavity “top shot” mold which allows you to use two injectors and a mixing block (not included) to shoot top/bottom laminated baits.
Aluminum Fishing Lure Molds
The 2 Inch Battle Grub measures 2 inches long from tip to tail and the thickest part of the body is .36″ in across. It has a grub shaped body for easy rigging on small jigs, a wide but flat tail that has lots of up/down action and spikes along both sides to add texture and more […]
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4